Shopping Cart

0 item Rs.0.00

My Cart -

0 item
My Cart: (0)
Categories
Compare Products

You have no items to compare.

Popular Tags

MotorDrivers

  1. Rs.300.00
    • H - Bridge IC breakout board
    • Switches up to 2 amps per channel
  2. Rs.399.00

    Module supply voltage: 2.5-12V
    Suitable for the motor range: motor operating voltage 2.5V-12V
    0.8A maximum operating current
    Size: 49mm x 36mm
    Color: Blue

  3. Rs.299.00
    • Voltage max: 16V
    •  Maximum current rating: 30 A
    •  Practical Continuous Current: 14 A
    •  Current sensing available to Arduino analog pin
    •  MOSFET on-resistance: 19 mΩ (per leg)
    •  Maximum PWM frequency: 20 kHz
    •  Thermal Shutdown
    •  Undervoltage and Overvoltage shutdown
    • Size: Approx. 54x28x10mm / 2.13x1.10x0.39inch
  4. Rs.2,599.00
    • Voltage max: 16V
    • Maximum current rating: 30 A
    • Practical Continuous Current: 14 A
    • Current sensing available analog pin
    • MOSFET on-resistance: 19 mΩ (per leg)
    • Maximum PWM frequency: 20 kHz
    • Thermal Shutdown
    • Undervoltage and Overvoltage shutdown
  5. Rs.1,499.00

    1、Peak current (Load): 50A

    2、Recommend max working current(Load): 20A

    3、Power VCC (Load): 0V~30V

    4、Recommend power vcc(load) : 12V ~ 26V

    5、Control VCC: 4V~12V

    6、Control TTL Voltage; 2.5V ~ 12V

  6. Rs.1,399.00

    *Double BTS7960 large current (43 A) H bridge driver;
    *5V isolate with MCU, and effectively protect MCU;
    *5V power indicator on board;
    *voltage indication of motor driver output end;
    *can solder heat sink;
    *Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2); *isolation chip 5 V power supply (can share with MCU 5 V); *Size: 4 * 5 * 1.2 cm;
    *Able to reverse the motor forward, two PWM input frequency up to 25kHZ; two heat flow passing through an error signal output;
    *isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply;
    *the supply voltage 5.5V to 27V

  7. Rs.189.00
    • Simple step and direction control interface
    • Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
    • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
    • Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
    • 45 V maximum supply voltage
    • Built-in regulator (no external logic voltage supply needed)
    • Can interface directly with 3.3 V and 5 V systems
    • Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
    • Short-to-ground and shorted-load protection
  8. Rs.779.00
    • Current level by adjustable to meet your various application requirements.
    • Automatic semi-flow adjustable.
    • Using 6N137 high-speed optical coupling to ensure high speed without losing step.
    • Board printed setup instructions, can use without a use manual
    • Using thick fine-toothed radiator, good heat dissipation
  9. Rs.210.00

    Can drive : 

    4 DC motors 

    2 stepper motors 

    Compatible with 

    UNO 

    MEGA and others

  10. Rs.129.00
    • Minimum operating voltage: 8V
    • Maximum operating voltage: 35V
    • Continuous current per phase: 1 Amp
    • Maximum current per phase: 2 Amp
    • Minimum logic voltage: 3V
    • Maximum logic voltage: 5.5V
    • Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
    • Reverse voltage protection?: No